The Bently Nevada 330101-00-30-90-02-05 is a 3300 XL 8 mm proximity probe for non-contact measurement of shaft vibration and position on rotating machinery. This exact ordering code specifies a 3/8-24 UNF probe without armor, 0.0 in unthreaded length, 3.0 in overall case length, 9.0 m total length, a standard cable with miniature coaxial ClickLoc connector, and code 05 CSA/ATEX/IECEx approvals.
| Manufacturer | Bently Nevada (Baker Hughes) |
| Complete part number | 330101-00-30-90-02-05 |
| Product family | 3300 XL 8 mm Proximity Transducer System |
| Probe type | 3/8-24 UNF thread, without armor |
| Primary use | Non-contact shaft vibration and axial/radial position measurement |
| Supply condition and availability | Confirmed in the written quotation; label and product photos can be requested before shipment |
| Warranty | Limited warranty terms are confirmed in the quotation or order confirmation |
The full suffix is important. Customers should compare every code position with the installed probe and system documentation before ordering.
| Code | Selected option | Meaning |
|---|---|---|
| 330101 | Base model | 3300 XL 8 mm probe, 3/8-24 UNF thread, without armor |
| 00 | Unthreaded length | 0.0 in unthreaded length |
| 30 | Overall case length | 3.0 in overall case length |
| 90 | Total length | 9.0 m (29.5 ft) total probe length |
| 02 | Connector and cable | Miniature coaxial ClickLoc connector with standard cable |
| 05 | Agency approvals | CSA, ATEX and IECEx approval option |
The 3300 XL 8 mm system uses eddy-current proximity measurement to provide an electrical output related to the distance between the probe tip and a conductive target. Typical uses include:
The 3300 XL 8 mm product family is designed for interchangeability between compatible probes, extension cables and Proximitor sensors. Interchangeability does not remove the need to match the correct system length, probe family, connector/cable option and approval requirements.
Important: code 90 identifies a 9.0 m total-length probe. It is intended for a compatible 9 m 3300 XL Proximitor sensor loop. Because the probe supplies the full 9 m total length, an additional extension cable is normally not used.
Do not substitute a 5 m probe/extension arrangement without checking the complete transducer loop. Before ordering, confirm the installed probe number, Proximitor sensor model, required system length, connector option, target material and hazardous-area requirements.
Before dispatch, Stockoems can verify the part number and visible label information, record the supplied product condition and provide photos on request. Inspection scope depends on the item, available test equipment and the written order requirements. Read our Quality Control and Company Verification pages for more information.
Worldwide shipping can be arranged by international express or other agreed logistics services. Freight, destination charges and applicable trade terms are confirmed in the quotation. See Shipping & Delivery, Warranty and Return Policy. Compatibility must be verified before purchase; incompatibility by itself does not establish a product quality defect.
Yes. In the official ordering structure, total-length code 90 means 9.0 m (29.5 ft).
Because this configuration already has a 9.0 m total length, it is normally connected to a compatible 9 m Proximitor sensor without an additional extension cable. Confirm the complete loop before installation.
Code 05 is the CSA, ATEX and IECEx approval option. If certification is mandatory, request a clear label photo and confirm the required documentation before ordering.
Only when the probe type, system length, connector/cable option, installation dimensions and approval requirements are compatible. Send both complete part numbers for comparison.
Yes. Product and label photos can be supplied on request, especially when a specific suffix, approval marking or condition is important.
Send the complete part number, quantity, destination and required delivery date to sales6@apterpower.com.
Send us the required quantity, destination and existing label photos. We will confirm supply condition, availability, inspection scope, warranty and shipping in writing.
Technical reference: Stockoems Technical Resources — 3300 XL 8 mm documentation
Independent reseller notice: Stockoems is operated by Apter Power Limited and is an independent reseller of industrial automation products. Manufacturer names and trademarks are used for identification purposes only. Product condition, availability and the exact supply scope are defined by the written quotation and confirmed order.
If you have other request contact our team to get customized service
Call +86 18159889985 to be connected with our Manager Stella
Email to sales6@apterpower.com get your best quotation
For the quick assistance message us on WhatsApp at +86 18159889985 now!We provide professional global shipping services to ensure your industrial automation parts and equipment arrive safely and on time. To meet different delivery requirements, we cooperate with internationally recognized logistics companies, including:FedEx/DHL/TNT/UPS/SF Express
Whether you require standard international shipping or urgent express delivery, we can arrange flexible logistics solutions tailored to your project schedule and destination.
For convenient and secure transactions, we accept T/T (Telegraphic Transfer) payment.
After order confirmation, our sales team will provide complete payment details and invoice information to ensure a smooth and efficient payment process.
We are committed to providing efficient delivery and dependable customer service for clients worldwide.
Always compare the complete ordering code and required system length before selecting an alternative.
| Related product | Why compare it |
|---|---|
| 330101-00-60-05-02-00 | Same 330101 probe family with different case and total-length options |
| 330104-00-10-05-01-BR | Metric M10 x 1 armored 3300 XL 8 mm probe configuration |
| 330130-045-00-05 | 3300 XL standard extension cable for compatible multi-component loops |
| 330180-X1-05 MOD 143416-02 | 3300 XL Proximitor sensor variant; compatibility must be confirmed |
