Bently Nevada 330101-04-36-05-02-05 3300 XL 8 mm Proximity Probe

Bently Nevada 330101-04-36-05-02-05 3/8-24 probe with 3.6 inch case and 0.5 m cable

Inquiry now

Bently Nevada 330101-04-36-05-02-05 3300 XL 8 mm Proximity Probe

Unarmored 3/8-24 UNF probe with 0.4 in unthreaded length, 3.6 in case and 0.5 m lead.

Product Overview

Bently Nevada 330101-04-36-05-02-05 is a standard 3300 XL 8 mm proximity probe for non-contact radial vibration and axial-position measurements. The complete suffix identifies 0.4 in unthreaded length, 3.6 in overall case length, 0.5 m total probe length, standard cable without connector protector, and CSA, ATEX and IECEx approvals.

The 3300 XL 8 mm probe is one component of a matched eddy-current transducer system. System performance depends on the correct extension cable, Proximitor Sensor length, target material, probe gap and mechanical installation.

Commercial Status

Manufacturer	Bently Nevada, a Baker Hughes business
Complete Part Number	330101-04-36-05-02-05
Product Family	3300 XL 8 mm Proximity Transducer System
Document Basis	Official datasheet 141194 Rev. AL
Configured Approval	CSA, ATEX and IECEx approvals
Lifecycle Status	Not stated for this exact configured part number in the current official datasheet

Verified Technical Data

Probe Type	3300 XL 8 mm standard-mount proximity probe
Probe Thread	3/8-24 UNF
Armor	Without armor
Unthreaded Length	0.4 in
Overall Case Length	3.6 in
Total Probe Length	0.5 m (1.6 ft)
Connector and Cable	Miniature coaxial ClickLoc connector; standard cable; no connector protector
Probe DC Resistance	7.45 ± 0.50 Ω for the 0.5 m probe
Probe Tip Material	Polyphenylene sulfide (PPS)
Probe Case Material	AISI 304 stainless steel
Matched-System Linear Range	2 mm (80 mils), approximately 0.25 to 2.3 mm from target
Recommended Radial Gap	Approximately 1.27 mm (50 mils), corresponding to -9 Vdc
Matched-System Scale Factor	7.87 V/mm (200 mV/mil) for the specified standard system
Typical Frequency Response	0 to 10 kHz, +0/-3 dB for the matched system

System Fit and Applications

Measurement Duties

Radial shaft vibration, radial position, axial thrust position, speed or phase-reference measurement in compatible 3300 XL monitoring arrangements.

Typical Machines

Turbines, compressors, pumps, motors and other rotating assets with suitable conductive targets and adequate mounting and side-clearance geometry.

Compatibility and Procurement Checks

Match the complete 330101-04-36-05-02-05 suffix; similar 330101 probes may differ in case and cable length.
For a 5 m system, verify a compatible 4.5 m 3300 XL extension cable with this 0.5 m probe.
Confirm the 3/8-24 UNF mounting interface, 3.6 in case length and 0.4 in unthreaded section.
Verify a compatible 3300 XL Proximitor Sensor, total system length and target-material calibration.
Check connector-protector requirements because option 02 supplies the standard ClickLoc connector without a protector.
Review target diameter, probe spacing and cross-talk limits before final installation.

Lifecycle Note

The official 3300 XL 8 mm datasheet defines this ordering configuration but does not state a manufacturer lifecycle designation for 330101-04-36-05-02-05. Confirm current supply status and approved system replacement strategy during procurement.

Frequently Asked Questions

What does the complete suffix specify?

It specifies a 0.4 in unthreaded section, 3.6 in case, 0.5 m cable, standard ClickLoc connection without protector, and listed approvals.

Can the probe be used alone?

No. It must be matched with the correct extension cable and 3300 XL Proximitor Sensor or compatible 1 m system arrangement.

What is the matched-system linear range?

The official 3300 XL 8 mm system linear range is 2 mm (80 mils) under the stated conditions.

What should be checked before ordering?

Confirm thread, dimensions, cable and total system length, connector protection, approvals, target material and Proximitor compatibility.

Verify 330101-04-36-05-02-05 Before Procurement

Contact Stockoems for availability verification, configuration review, warranty terms and worldwide delivery coordination.

Email: sales6@apterpower.com | WhatsApp: +86 181 5988 9985

Request Product Support WhatsApp Sales

Industrial Spare Parts Support for 330101-04-36-05-02-05

Structured verification, condition review, logistics coordination and post-delivery support for critical automation and machinery-monitoring spares.

Procurement Support Workflow

1. Part-Number Verification

We review the complete suffix, product family, thread, case length, cable length, connector and approval configuration against available documentation.

2. Compatibility Review

Your installed extension cable, Proximitor Sensor, total system length, target material and mounting arrangement are checked before order confirmation.

3. Condition and Evidence

When available, label, connector, armor, probe-tip and packaging photographs support a practical pre-shipment condition review.

4. Packing and Logistics

Protective packing, courier options, export documentation and worldwide delivery coordination are arranged for sensitive industrial components.

5. Warranty Coordination

Warranty terms, inspection scope and handling requirements are clarified before dispatch so procurement records remain traceable.

6. Technical Follow-Up

Post-delivery assistance can cover received-part verification, documentation matching and escalation of configuration discrepancies.

Service Environment

Stockoems industrial spare parts service office

Responsive inquiry handling and order coordination

Stockoems technical verification workspace

Documentation and configuration review

Global logistics and after-sales communication

Information to Send With Your Inquiry

Complete part number and clear nameplate photographs
Installed probe, extension cable and Proximitor Sensor numbers
Required quantity, destination country and requested delivery date
Condition preference and required certificates or inspection records
Application notes covering machine type, target material and mounting restrictions