Bently Nevada 330101-04-36-10-02-05 3300 XL 8 mm Proximity Probe

Bently Nevada 330101-04-36-10-02-05 3/8-24 probe with 3.6 inch case and 1.0 m cable

Inquiry now

Bently Nevada 330101-04-36-10-02-05 3300 XL 8 mm Proximity Probe

Unarmored 3/8-24 UNF probe with 0.4 in unthreaded length, 3.6 in case and 1.0 m lead.

Product Overview

Bently Nevada 330101-04-36-10-02-05 is a standard 3300 XL 8 mm proximity probe for non-contact shaft vibration and position monitoring. Its complete ordering code defines a 0.4 in unthreaded section, 3.6 in overall case length, 1.0 m total probe length, standard cable without connector protector, and CSA, ATEX and IECEx approvals.

Unlike the otherwise similar 0.5 m configuration, this exact model has a 1.0 m probe lead and different nominal probe resistance. It must be reviewed as part of the complete matched 3300 XL system.

Commercial Status

Manufacturer	Bently Nevada, a Baker Hughes business
Complete Part Number	330101-04-36-10-02-05
Product Family	3300 XL 8 mm Proximity Transducer System
Document Basis	Official datasheet 141194 Rev. AL
Configured Approval	CSA, ATEX and IECEx approvals
Lifecycle Status	Not stated for this exact configured part number in the current official datasheet

Verified Technical Data

Probe Type	3300 XL 8 mm standard-mount proximity probe
Probe Thread	3/8-24 UNF
Armor	Without armor
Unthreaded Length	0.4 in
Overall Case Length	3.6 in
Total Probe Length	1.0 m (3.3 ft)
Connector and Cable	Miniature coaxial ClickLoc connector; standard cable; no connector protector
Probe DC Resistance	7.59 ± 0.50 Ω for the 1.0 m probe
Probe Tip Material	Polyphenylene sulfide (PPS)
Probe Case Material	AISI 304 stainless steel
Matched-System Linear Range	2 mm (80 mils), approximately 0.25 to 2.3 mm from target
Recommended Radial Gap	Approximately 1.27 mm (50 mils), corresponding to -9 Vdc
Matched-System Scale Factor	7.87 V/mm (200 mV/mil) for the specified standard system
Typical Frequency Response	0 to 10 kHz, +0/-3 dB for the matched system

System Fit and Applications

Measurement Duties

Radial vibration, shaft position, axial thrust, speed and phase-reference measurement when integrated with the correct 3300 XL system components.

Installation Context

Rotating machinery using a 3/8-24 UNF probe mount and 1.0 m lead, with cable routing and system-length requirements checked against the installed Proximitor Sensor.

Compatibility and Procurement Checks

Match the complete 330101-04-36-10-02-05 suffix and do not substitute the 0.5 m version without reviewing system length.
A 1.0 m system may use the probe directly with the correct 1 m Proximitor Sensor; for a 5 m system, verify a compatible 4.0 m extension cable.
Confirm the 3/8-24 UNF mounting interface, 3.6 in case length and 0.4 in unthreaded section.
Verify target material, Proximitor Sensor calibration and total electrical system length.
Option 02 supplies no connector protector; determine whether environmental protection is required.
Review target diameter, side clearance and cross-talk spacing for the actual machine geometry.

Lifecycle Note

The official 3300 XL 8 mm datasheet defines this configuration but does not state a manufacturer lifecycle designation for 330101-04-36-10-02-05. Confirm current supply status and complete-system compatibility before procurement.

Frequently Asked Questions

How does this model differ from the 0.5 m version?

Its total probe length is 1.0 m and its nominal probe resistance is 7.59 ± 0.50 Ω.

Can it connect directly to a Proximitor Sensor?

It can form a correctly specified 1 m system, but the exact Proximitor Sensor and any extension cable must match the intended total length.

Does the connector include a protector?

No. Connector option 02 is the standard miniature ClickLoc connector without a protector.

What should be checked before ordering?

Confirm complete suffix, dimensions, 1.0 m length, system electrical length, approvals, target calibration and mounting geometry.

Verify 330101-04-36-10-02-05 Before Procurement

Contact Stockoems for availability verification, configuration review, warranty terms and worldwide delivery coordination.

Email: sales6@apterpower.com | WhatsApp: +86 181 5988 9985

Request Product Support WhatsApp Sales

Industrial Spare Parts Support for 330101-04-36-10-02-05

Structured verification, condition review, logistics coordination and post-delivery support for critical automation and machinery-monitoring spares.

Procurement Support Workflow

1. Part-Number Verification

We review the complete suffix, product family, thread, case length, cable length, connector and approval configuration against available documentation.

2. Compatibility Review

Your installed extension cable, Proximitor Sensor, total system length, target material and mounting arrangement are checked before order confirmation.

3. Condition and Evidence

When available, label, connector, armor, probe-tip and packaging photographs support a practical pre-shipment condition review.

4. Packing and Logistics

Protective packing, courier options, export documentation and worldwide delivery coordination are arranged for sensitive industrial components.

5. Warranty Coordination

Warranty terms, inspection scope and handling requirements are clarified before dispatch so procurement records remain traceable.

6. Technical Follow-Up

Post-delivery assistance can cover received-part verification, documentation matching and escalation of configuration discrepancies.

Service Environment

Stockoems industrial spare parts service office

Responsive inquiry handling and order coordination

Stockoems technical verification workspace

Documentation and configuration review

Global logistics and after-sales communication

Information to Send With Your Inquiry

Complete part number and clear nameplate photographs
Installed probe, extension cable and Proximitor Sensor numbers
Required quantity, destination country and requested delivery date
Condition preference and required certificates or inspection records
Application notes covering machine type, target material and mounting restrictions