Bently Nevada 330102-00-12-10-01-05 3300 XL 8 mm Proximity Probe

Bently Nevada 330102-00-12-10-01-05 armored 1 metre ClickLoc proximity probe

Inquiry now

Bently Nevada 330102-00-12-10-01-05 3300 XL 8 mm Proximity Probe

Armored 1 metre 8 mm probe with 3/8-24 UNF thread, ClickLoc connector and multiple hazardous-area approvals.

Product Overview

Bently Nevada 330102-00-12-10-01-05 is a 3300 XL 8 mm proximity probe configured with a 3/8-24 UNF threaded armored case. The exact suffix specifies 0.0 inch unthreaded length, 1.2 inch overall case length and 1.0 metre total length.

Its miniature coaxial ClickLoc connector includes a connector protector and the approval option covers CSA, ATEX and IECEx. The probe is intended for compatible 3300 XL proximity transducer systems used on rotating machinery.

Commercial Status

Manufacturer	Bently Nevada
Complete Part Number	330102-00-12-10-01-05
Product Family	3300 XL 8 mm Proximity Transducer System
Accurate Product Type	3300 XL 8 mm Proximity Probe
Official Lifecycle Wording	Not stated in the exact official Baker Hughes datasheet reviewed; no lifecycle status is inferred.

Verified Technical Data

Parameter	Official Value for 330102-00-12-10-01-05
Probe type	3300 XL 8 mm probe with armor
Thread	3/8-24 UNF
Unthreaded length	0.0 in
Overall case length	1.2 in
Total length	1.0 m (3.3 ft)
Connector option	Miniature coaxial ClickLoc connector with connector protector
Cable option	Standard cable
Approvals	CSA, ATEX and IECEx
Probe tip diameter	8.0 mm
Nominal probe DC resistance	7.59 ± 0.50 Ω for a 1 m probe
System linear range	2 mm (80 mil), approximately 0.25 to 2.3 mm
Standard system scale factor	7.87 V/mm (200 mV/mil) ±5% for 1 m and 5 m systems
Frequency response	0 to 10 kHz, +0/-3 dB
Minimum flat target diameter	15.2 mm
Minimum shaft diameter	50.8 mm; 76.2 mm recommended
Case material	AISI 303 or 304 stainless steel
Standard cable	75 Ω triaxial cable

Source basis: Baker Hughes Bently Nevada official 3300 XL 8 mm Proximity Transducer System datasheet, including the exact order-number key.

System Fit and Applications

Shaft Vibration Monitoring

Supports radial shaft vibration measurement when installed with the correct extension cable and Proximitor sensor.

Axial Position Measurement

Can support axial or thrust-position monitoring when target geometry and mechanical installation meet the system requirements.

Machine Protection Integration

Fits rotating-machinery monitoring architectures that specify the 3300 XL 8 mm transducer system and exact cable length.

Compatibility and Procurement Checks

Confirm the complete order number 330102-00-12-10-01-05, including every two-digit suffix field.
Verify the 3/8-24 UNF thread, 1.2 inch case length, armor and 1.0 metre total length against the installed probe.
Match the probe, extension cable and Proximitor sensor as a compatible 3300 XL system with the required total electrical length.
Check ClickLoc connector style, connector protector and cable routing before installation.
Confirm CSA, ATEX and IECEx approval requirements for the installation location.

Lifecycle Note

The exact official Baker Hughes datasheet confirms the complete 330102-00-12-10-01-05 configuration but does not state an official lifecycle label. This page therefore does not classify the product as Active, Legacy, Obsolete or any other lifecycle state. Supply and replacement status should be checked at the time of procurement.

Frequently Asked Questions

What is Bently Nevada 330102-00-12-10-01-05?

It is an armored 3300 XL 8 mm proximity probe with 3/8-24 UNF thread, 1.2 inch case length and 1.0 metre total length.

What connector is supplied?

The exact suffix specifies a miniature coaxial ClickLoc connector with a connector protector and standard cable.

Which approvals are included?

The 05 approval suffix covers CSA, ATEX and IECEx according to the official order-number key.

Can it replace any 3300 XL probe automatically?

No. Thread, case length, total electrical length, connector, armor and approval suffixes must match the installed system.

What should be checked before ordering?

Verify the complete suffix, mechanical dimensions, system cable length, compatible Proximitor sensor, target geometry and hazardous-area requirements.