Bently Nevada 200151-60-03-10 Accelerometer Interface Cable

200151-60-03-10 6 m armored accelerometer interface cable product and nameplate

Inquiry now

Product reference: 200151-60-03-10

Bently Nevada 200151-60-03-10 Accelerometer Interface Cable — Product Overview

200151-60-03-10 is listed as an industrial cable or interface component. Similar-looking cables can differ in length, jacket, armor, connector and system compatibility, so selection should be based on the complete part number rather than appearance alone.

Stockoems is an independent reseller of industrial automation products. Manufacturer names and part numbers are used for identification only; the written quotation and confirmed order requirements define the product supplied.

ManufacturerBently Nevada

Model / part number200151-60-03-10

Product typeIndustrial cable or interface component

What to Verify Before Ordering 200151-60-03-10

Confirm cable length, jacket and armor option, connector protection, environmental requirement and compatibility with both ends of the installed measurement or control system.

Send a clear nameplate photo when an exact replacement or compatibility check is required.
State the required quantity, product condition, destination country and requested delivery date.
Confirm any mandatory revision, certificate, original packaging or manufacturer documentation before quotation approval.

200151-60-03-10 Frequently Asked Questions

What information is needed to quote 200151-60-03-10?

Please provide the complete part number, quantity, destination, required condition and clear label photos. Include the installed system or mating component when compatibility matters.

Can a similar-looking unit replace 200151-60-03-10?

Not necessarily. Matching appearance or a partial model number does not confirm electrical, mechanical, firmware or system compatibility. Verify the complete ordering code and application.

Can Stockoems provide inspection photos and shipping details?

Where available, product and label photos can be confirmed before shipment. Shipping method, cost and estimated dispatch information are stated in the quotation or order confirmation.

Order confidence and supportAccelerometer technical resources · Quality Control · Company Verification · Shipping & Delivery · Warranty · Return Policy · Request a Quote

INSTALLATION & ROUTING GUIDE

200151-60-03-10 Accelerometer Interface Cable

A purchasing page built around the cable path: length, armor, connector retention and routing conditions are checked before the part reaches site.

FIRST FIELD
60
6.0 m cable length

→

SECOND FIELD
03
Blue armored cable

→

THIRD FIELD
10
Enhanced coupling nuts, both ends

Before routing

Measure the physical route, not the straight-line distance.
Include service loops and connector access.
Separate the signal cable from high-power conductors.
Confirm both mating connectors before release.

Cable construction

Four 22 AWG conductors; braided shield with drain wire and at least 85% coverage; PVC outer jacket.

When correctly mated, the connector seal is rated IP67.

Bend radius & environment

Operating temperature	−20 to +100 °C
Minimum bend radius	63.5 mm
Maximum standard family length	25 m
This configuration	6 m, blue armored, enhanced coupling nuts on both ends

Cable path worksheet

A. Sensor connector

B. Route length

C. Bend / heat zones

D. Monitor connector

Attach a route sketch or old-cable label to the inquiry. This often prevents an avoidable length or connector mismatch.

Purchase pack: old label + route length + connector photos + quantity
Send route details on WhatsApp

Source: Stockoems Technical Resources — 200150/200155/200157 accelerometer documentation. Stockoems is an independent supplier.

How customers avoid ordering the wrong 200151-60-03-10 cable

A Bently Nevada 200151-60-03-10 replacement cable must match three purchasing decisions simultaneously: the 6 m length, blue armored construction and enhanced coupling nuts at both ends. A cable that looks similar may have a different length code, armor option or connector retention arrangement.

The quoted route should include bends, entry points, cable tray changes, service loops and connector-access allowance. Measure the path from the sensor connector to the monitoring-side connection. Do not calculate a 6 m armored accelerometer interface cable from straight-line distance alone.

Route calculation example

Machine run
4.6 m+ Bends / tray
0.5 m+ Service access
0.4 m= 5.5 m route
check whether 6 m is suitable

This example illustrates the method only. Site routing and engineering rules determine the actual allowance.

Connector-end inspection

Photograph both old-cable connector faces
Check threads and coupling-nut condition
Record any backshell or armor damage
Identify oil, water or washdown exposure
Confirm required ingress protection when mated

Installation controls

Respect the 63.5 mm minimum bend radius
Keep away from excessive heat and sharp edges
Support the route so connector loads are limited
Separate low-level signal wiring from power cables
Do not energize or commission until connections are verified

Procurement questions for an armored accelerometer cable

Is 6 m the selected code or only an estimate? Provide a measured route and desired allowance.
Is armor required along the complete run? State the mechanical exposure and existing construction.
Are enhanced coupling nuts required at both ends? Confirm against the old cable and mating devices.
What commercial evidence is needed? Request condition, availability, warranty, label photos and offered documentation.

RFQ worksheet — 200151-60-03-10

□ Actual measured route

□ Service-loop allowance

□ Sensor-end connector photo

□ Monitor-end connector photo

□ Armor / mechanical exposure

□ Temperature and washdown conditions

□ Quantity and destination

□ Required delivery date

Ask the offer to identify exact ordering code, condition, availability, warranty and estimated dispatch.

Email cable RFQ WhatsApp route review

Source and review: construction and environmental values are based on the official Bently Nevada accelerometer documentation. Installation suitability remains site-specific. Reviewed 12 August 2026.

CABLE LOGISTICS & PACKING PLAN

200151-60-03-10 Delivery Service

The 6 m armored cable is checked and packed around connector protection, coil diameter, routing readiness and shipment traceability.

01 — Code check
60 length / 03 armor / 10 enhanced nuts

02 — Coil safely
Respect bend radius and avoid crushing

03 — Protect ends
Connector faces and coupling threads covered

04 — Dispatch
Carrier and tracking supplied

Packing controls for an armored interface cable

Cable coiled without violating the 63.5 mm minimum bend radius
No sharp tie pressure applied to the cable jacket or armor
Both connectors separated and protected from impact
Part-number label kept visible for receiving inspection
Moisture and abrasion protection selected for the shipping route
Outer carton sized to prevent movement during courier handling

Payment & shipping

Payment: T/T bank transfer, Alipay or another method confirmed on the formal PI.

Carriers: DHL, FedEx and SF; selection depends on destination, service availability and agreed freight.

Timing: availability and estimated dispatch are stated in the offer; transit time starts after carrier collection.

Receiving inspection

□ Compare label with 200151-60-03-10 purchase order

□ Inspect outer carton before opening

□ Check both connector faces and coupling nuts

□ Inspect armor and jacket for crushing or cuts

□ Preserve packing and courier label if damage is found

□ Send photos and invoice number to after-sales support

Warranty: Stockoems states a one-year warranty for product quality issues. Final scope, exclusions and claim handling follow the quotation/PI; transit damage should be reported promptly with packaging evidence.

Request landed cost and delivery options
Send quantity, full delivery address/postal code and required date.
Email logistics RFQ

Freight, Incoterm, duties/taxes and payment instructions are valid only when stated in the written commercial offer.

CURRENT ROUTE
60 / 03 / 10
6 m • blue armored • enhanced nuts both ends

If the route changes, compare these codes

200151-60-02-10: same nominal length and coupling option; verify non-armored construction is acceptable.
200151-60-03-00: armored 6 m route; verify standard coupling nuts meet the site need.
200152 family: do not cross-select by cable length alone; compare end connectors and intended sensor system.

Length-selection warning: use the next suitable official length option when 6 m cannot accommodate the measured route and service allowance; do not stretch, splice or force a short cable.

FILE-BASED CABLE CHECK

Same-family vs cross-family

Models found in the supplied weekly stock lists and matched to Bently Nevada.

Only 200151-040-03-10 belongs to the same accelerometer-interface cable family. The 330130 and 330930 entries are proximity-system extension cables and must not be used as substitutes.

Model from text	Matched brand / product family	Compatibility status	Source file
200151-040-03-10	Bently Nevada · accelerometer interface cable	Same family — compare length field with 200151-60-03-10 and verify catalog formatting.	7.6-7.10.txt
330130-040-00-05	Bently Nevada · 3300 XL extension cable	Cross-family — proximity-transducer cable, not an accelerometer cable.	7.13-7.17.txt
330130-045-00-05	Bently Nevada · 3300 XL extension cable	Cross-family — verify probe/Proximitor chain separately.	7.13-7.17.txt / 7.20-7.24.txt
330130-075-01-05	Bently Nevada · 3300 XL extension cable	Cross-family — different cable system and options.	7.6-7.10.txt
330930-045-02-00	Bently Nevada · 3300 NSv extension cable	Cross-family — NSv cable; not interchangeable with 200151.	7.13-7.17.txt
330930-045-02-05	Bently Nevada · 3300 NSv extension cable	Cross-family — confirm the complete NSv chain.	7.6-7.10.txt

RFQ tip: copy the exact line from the old cable label and attach both connector photographs. Similar length numbers do not establish electrical or mechanical compatibility.

Tags :