Product reference: 22811-00-03-05-02
22811-00-03-05-02 Bently Nevada 7200 Series 8mm Proximity Probe M10x1 Thread, 30mm Case, 0.5m Cable — Product Overview
22811-00-03-05-02 is listed as an industrial cable or interface component. Similar-looking cables can differ in length, jacket, armor, connector and system compatibility, so selection should be based on the complete part number rather than appearance alone.
Stockoems is an independent reseller of industrial automation products. Manufacturer names and part numbers are used for identification only; the written quotation and confirmed order requirements define the product supplied.
ManufacturerBently Nevada
Model / part number22811-00-03-05-02
Product typeIndustrial cable or interface component
What to Verify Before Ordering 22811-00-03-05-02
Confirm cable length, jacket and armor option, connector protection, environmental requirement and compatibility with both ends of the installed measurement or control system.
- Send a clear nameplate photo when an exact replacement or compatibility check is required.
- State the required quantity, product condition, destination country and requested delivery date.
- Confirm any mandatory revision, certificate, original packaging or manufacturer documentation before quotation approval.
22811-00-03-05-02 Frequently Asked Questions
What information is needed to quote 22811-00-03-05-02?
Please provide the complete part number, quantity, destination, required condition and clear label photos. Include the installed system or mating component when compatibility matters.
Can a similar-looking unit replace 22811-00-03-05-02?
Not necessarily. Matching appearance or a partial model number does not confirm electrical, mechanical, firmware or system compatibility. Verify the complete ordering code and application.
Can Stockoems provide inspection photos and shipping details?
Where available, product and label photos can be confirmed before shipment. Shipping method, cost and estimated dispatch information are stated in the quotation or order confirmation.
Product datasheet
| Model number |
22811-00-03-05-02 |
|
| Manufacture |
Bently Nevada |
|
| System |
TSI |
|
|
Condition
|
Brand New |
|
|
Country of Origin
|
USA |
|
|
HS Code
|
8537101190 |
|
|
After-Sales Support
|
12-months |
|
Product information
22811-00-03-05-02 is a Bently Nevada 7200 series 8mm proximity probe featuring standard metric M10x1 threads. Fully compatible with legacy monitoring infrastructures, this unarmored unit works seamlessly with 7200 Proximitors to deliver a stable 80-mil (2 mm) linear displacement range and highly reliable machinery vibration feedback.
Specifications
Model: 22811-00-03-05-02 (8 mm Standard Probe)
Tip Construction: Standard
Case Thread: M10 × 1 (metric)
System Length: 5 metres (16.4 feet) combined probe and extension cable
Calibrated Range: 80 mils (2.0 mm), beginning at approximately 10 mils from probe face
Scale Factor: 200 mV/mil (7.87 V/mm) within ±4% when calibrated as a system
Frequency Response: 0 Hz DC to 10 kHz (0 to 600,000 cpm)
Power Requirement: -17.5 Vdc to -26 Vdc at 12 mA maximum consumption
Dimensions：1.8x1.5x96cm
Weight：0.06kg
Application
-
Radial Vibration Monitoring: Detects bearing condition and identifies rotor imbalance and misalignment in rotating machinery.
-
Axial Thrust Position Measurement: Assesses thrust bearing wear to prevent potential bearing failure.
-
Rotor Stability Analysis: Determines attitude angle by measuring shaft average radial position.
-
Diagnostic Data Collection: Provides vibration amplitude and phase angle for Polar and Bode format plotting.
-
Eccentricity Measurement: Monitors rotor bow during startup and low-speed rotation.
System Compatibility & Alternative Models
- System Compatibility: Fully compatible with Bently Nevada 18745-series 7200 Proximitor Sensors (such as the 5-meter 18745-03 module), 21747 standard or armored extension cables, and legacy 3300 or 9000 Machinery Monitoring Systems.
- Alternative Model: 22810-00-03-05-02
- Key Differences: The 22811-00-03-05-02 is constructed as an unarmored standard configuration, leaving its FEP-insulated coaxial leading cable exposed for flexible routing inside protected conduits. Conversely, the 22810-00-03-05-02 is an armored model variant that integrates an outer stainless steel protective armor sleeve over the internal cable lead to defend against physical crushing, tearing, and aggressive mechanical abrasion on the factory floor.
System Compatibility & Alternative Models
- System Compatibility: Fully compatible with Bently Nevada 18745-series 7200 Proximitor Sensors (such as the 5-meter 18745-03 module), 21747 standard or armored extension cables, and legacy 3300 or 9000 Machinery Monitoring Systems.
- Alternative Model: 22810-00-03-05-02
- Key Differences: The 22811-00-03-05-02 is constructed as an unarmored standard configuration, leaving its FEP-insulated coaxial leading cable exposed for flexible routing inside protected conduits. Conversely, the 22810-00-03-05-02 is an armored model variant that integrates an outer stainless steel protective armor sleeve over the internal cable lead to defend against physical crushing, tearing, and aggressive mechanical abrasion on the factory floor.
Ordering Information
|
Model Series
|
Type / Thread
|
Option A: Unthreaded Length
|
Option B: Overall Case Length
|
Option C: Total Lead Length
|
Option D: Connector Option
|
|
22811
|
Standard Mount, Unarmored (M10x1 Thread)
|
00 (0 mm)
|
03 (30 mm)
|
05 (0.5 meter / 20 inches)
|
02 (With miniature male coaxial connector)
|
For the quick assistance message us on WhatsApp at 
